ZIROHigh Speed 3D Printer Filament, HS-PLA Fast Printing 1.75mm, Dimensional Accuracy +/-0.02mm, High Flow Speedy PLA 30-600mm/s, 1kg/2.2lb, White

I had a large print to run (4 days). I have had issues in the past where the print had to be abandoned due to filament issues.Using this filament it ran through non stop without any problems whatsoever. Stuck to the bed like glue and produced a really high quality finish. Have already ordered some more!

I have used a lot of different filament brands since starting 3D printing and Ziro is the best I have used! I always get very high quality prints and really recommend their stuff! Since starting my side business 3D printing, it’s the only filament brand I order from now.What’s really helpful, with every roll of filament, they supply a sealing bag to protect it from moisture as well samples of filament to try out different colours. Really recommend!

I've used around half of this spool and so far it has produced reasonable results. I get a bit of stringing between point on the print but i havent tried to tune these out yet. I suspect a bit more retraction will sort it on my Anycubic Predator. The print quality otherwise is good, with a nice glossy finish. Bed adhesion on the ultrabase has been consistent. On the whole, I'd buy another reel and I'll see if I can tune out the stringing or use my Anet which has a direct drive extruder and hardly ever suffers this problem. I've dropped this a star since my last review as I bought a roll of Yellow PLA of the same brand and it's been a bit disappointing. The colour is very washed out compared to the Esun filament previously used and it's not sticking to the bed where the finer detail is, such as small holes and sharp corners. Maybe I've got a duff roll because the blue seemed ok and was a vibrant colour. It's like I got a Friday afternoon roll, just before they turned out the factory lights for the weekend.

Ziro is one of those filament makers that has batches of good and bad filament.i've had filament from them that was horrible to use, acting as if it was wet, but after drying repeatedly it would not stick or print well.This reel of filament has been a pleasure to use, sticks to the PEI sheet well, good quality prints.. but i do use a prusa printer, so that is part of the equation.It's a lovely shade of blue,

Ziro filament has been the backbone to my business for three years now. I always use it for my products ( Ant nests) and have found it to be the most consistent and nicest printing filament for the job. Even on Bambu printers at their high speeds it prints well! I can recommend to anyone. The included filament sample + cleaning filament is always nice, and getting a bag to store it is a great bonus too.

This is the try third type of Ziro filament I’ve bought, the other two being high speed white and mystical green. Each one has been perfect. The winding is neat and am yet to have a tangle. The print quality is spot on and the value for money is the icing on the cake. Would 100% recommend

Using at 220c hot end and 70c bed on Ender 5 pro, with sugar coated Borosilicate glass (see YouTube if you don't know what that's all about). Sticks to the bed really well during printing (really well!) and just pops off by itself when it cools to 38c with no effort at all (you hear a pop and then lift your print off with 2 fingers). The quality of the prints are spot on, with the standard benchy boat not having a single sign of stringing/sagging or any blemishes, a perfect print! If you get any under extrusion/head clogging firstly back the tension right off on your feeder and leave it there as this filament does not like high tension as the gears leave indent marks in the filament and causes it to grip in the bowden tube (even upgraded tube). If you have blobs in your prints (pimples) go to your slicer (I use Cura) and find 'mesh fixes' turn the maximum resolution to 0.5mm, maximum travel resolution to 0.5mm and maximum deviation to 0.025mm, that will cure it. I just purchased many more rolls of this filament as I am now getting through at least a roll every week as this is now my 'go-to' reliable filament...

The filament was well packaged as it arrives with silica desiccant included to prevent the build-up of humidity (which is quite common). The recommended printing temperature printed on the box was useful, and the print turned out beautifully as shown in the figure. Ziro is also quite thoughtful to also include a re-sealable plastic bag to store your filament. This is something that other filament company should be doing.I like the fact that the spool holder is transparent, allowing you to estimate the amount of filament left on the spool. The spool holder also has holes to hold the filament in place to prevent tangling during storage. Despite it is not very eco-friendly (many companies like filamentive and proto-pasta opt for cardboard spool holders), it does the job.The print came out beautifully with very bright and saturated colour - plenty of pigments (as advertised). It adheres well to the print surface (glass bed with hair spray) without any warping. With the right print setting, I can completely eliminate stringing. The bond between layer is also very strong, resulting in a strong and rigid print as you'd expect from a high-quality PLA filament.Overall I'd recommend this product.

Very nice and shiny

The media could not be loaded.  I absolutely love the colors. I need a shade of pink but unfortunately, this pink is not the pink that I actually need it for a project that I’m going to use. I love the fact that it comes with a sample of printer cleaner, and also a sample of filament. The seller is amazing and it looks like the product would be amazing if it was what I was actually looking for. I know it can be hard to gauge the actual colors because pictures and monitors are different. Again, the pink is beautiful it’s just not the shade of pink that I’m looking for at the moment. I also love that it comes with a storage pouch.

Did a manual filament swap on a Voron cube so you don’t have to. All these colors are working fine for me. Love the back light possibilities. Reasonable price. Smooth print at 210/65-60.Will be my go-to for clear filament.

Sono stato tentato dal prezzo molto basso per un PLA HighSpeed, già dai primi test di calibrazione è risultato un ottimo filamento..con Orcaslicer ho eseguito il testo volumetrico e il risultato è stato impeccabile ! nessun errore, velocità volumetrica settata a 23 !La stampa finale risulta un nero opaco.La bobina non mostra intrecci, nella confezione ho trovato un filamento per la pulizia dell'hotend e una busta ermetica con silica gelPrenderò sicuramente altri filamenti di questa marca

zelfs nog 2 keer 5m monsters om te testen meegeleverd, het filament komt in een hersluitbare zak. TOP!!