Omix-Ada | 12035.50 | Cup Holder, Dual | OE Reference: CH-1 | Fits 1984-1996 Jeep Cherokee XJ

Perfect addition for my Jeep. Previously had to mess with holding drinks between my legs or trying to shove them in between the seats and make sure they’re stable, but with these cup holders I don’t have to worry about that anymore. This will fit most drinks fine, for example a large drink from McDonald’s will fit snug and not move but anything larger or taller won’t fit or will tip over. I do wish the cup holders were deeper but for what it is and for the price it holds up just fine for me.

Installed in 1 minute on my 96 XJ. No issues - I do find it fits cans (12oz/16oz) really well, but larger things sometimes don't fit super happily. I think most people fix this by cutting the bottom out of it...but for me I usually have cans or smaller drinks. Works great for me!

Makes it harder to shift with the manual, better more clean option if you need a cup holder. Not a bad product at all. Big cups touch eachother perfect for cans and other small cups.

The media could not be loaded. The good:This product has a good build quality, the plastic feels sturdy and doe not feel cheaply made.The bad:As made evident by the pictures above, the cup holder does not hold anything very well. My drink came completely out of the cup holder and spilled in my jeep after a slightly ubrupt stop. It holds cans and smaller cups alright but there is still a gap. A gap is not an issue with normal cup holders, however, since these are so shallow the inertia of whatever is in the cup holder often times causes cans ans cups to fall out.A way to improve this design would be to make them deeper, and slightly wider at the top as they do not fit some of the larger sized cups.

It's a good product if you don't need a huge drink; coffee cups and soda cans work best. If you drive a stick shift, or work on your XJ often (if you own an XJ you surely work on it often), it can be difficult to engage the hand brake. The colour matched and it reuses the two screws that are already there, very simple to install. Overall, it's a lot better than nothing and that's something.

Takes up a ton of room in between the seats while blocking the majority of the E-brake. Like, to the point where it's nearly impossible to deploy the e-brake, because you can't get your entire hand around it when this is installed. It sits forward at an angle that is ridiculous, while claiming to take up a "small footprint", because the "TOP" part of it is small-ish.Reality? Look at your Cherokee, open the center glove box, look down -- the two black screws that are holding the plastic on either side of the "latch" that clicks and latches the center box closed? Those will match the "tabs" in the picture. Then the "drink holder" will sit forward EIGHT INCHES over your emergency break. You will have roughly 2-3 inches left of the actual break itself, including the "button" on the end which you have to press down a full 3/4" of an inch to actually release the handle to deploy the break.Congratulations, you have officially covered and semi-permanently blocked your ability to use your emergency break in, you know, emergencies.The good news is, this is very solid ABS plastic, so --- it won't break, even if left in the boiling hot sun, in the Jeep. So, if an emergency does happen --- don't even dream of being able to snap it off to reach that E-Brake.Oy-vey, this was NOT a well designed aftermarket....Trust me, remove the lid to your glove box, take it to your shop, dremel the drink holder size you want, seal the work with liquid TPE that matches, or hot melt (or re-cover the piece in liquid rubber, for all that if you want it to look new-ish) -- and have your own custom piece. Done.

I put this in my 1986 AMC Jeep Cherokee Pioneer, I love it!! There are no cup holders in the vehicle factory, so this is definitely an improvement and it fits perfectly. If you’re someone who likes to drive crazy and skkrttt skkrrttt maybe it’s not for you because it does make it difficult to utilize the E Brake. However you could cut out the middle portion as someone else in the reviews did, and you’d still be able to use the cup holders. You could even cut the outer edges off and make it thin enough to fit in the center console if you have lost your center console lid like I did. I like it though, it improves my life just how it is.

It installs just fine, it's good quality, but it's basically useless because it isn't very deep and doesn't fit my coffee mug. Holds a beer can, so...yay.